Jump to content

Costs ยท Stockton

Cost of replacing an electrical panel

Replacing an electrical panel typically runs about $1,500 to $4,000 in national price guides, and more when the meter or service changes. Here is what moves the number.

  1. Fill in the form. It takes about two minutes.
  2. A local specialist gets in touch. They ask a few questions and quote.
  3. You choose. Go ahead only if the price suits you.
a residential electrical service panel with a closed gray door and neatly labeled breakers in a garage wall

Request an electrician quote

A few details about the job, and a local specialist will contact you with a price.

Needed so the business can price the job properly.

Replacing an electrical panel typically costs about $1,500 to $4,000 in national price guides. A like-for-like swap sits at the low end. Moving from 100 to 200 amps, changing the meter base or fixing old wiring pushes the price up. Your electrician's written quote overrides every figure here. This page is the cost side of the electrical panel upgrade guide, and it shows what each line of a quote usually covers.

How much does it typically cost to upgrade an electrical panel?

Most 2026 price guides put a main panel replacement at roughly $1,500 to $4,000. A full service upgrade with a new meter base runs about $2,500 to $6,000, and costs can climb further if the utility has to replace the line.

The range is wide because "panel upgrade" covers different jobs. A basic swap of a 100-amp panel is one job. A 200-amp service upgrade with a new meter base and heavier wire is another. Always ask which job a quote describes.

JobTypical range
Main panel replacement$1,500 to $4,000
Subpanel$500 to $1,500
Full service upgrade with new meter base$2,500 to $6,000
Whole-home surge protector$200 to $800

These come from national price guides. They are not Stockton quotes.

How much do electricians charge to replace a panel?

Electricians usually price a panel by the job, not the hour. A job price rolls in the panel, breakers, labor, the permit run, the shutoff and testing. National price guides put electrician labor between about $50 and $130 an hour, and service call fees between about $100 and $200.

A panel swap often takes a day, but the price depends on what is behind the panel. Old cloth-covered wiring, missing grounds, crowded boxes and a panel in a tight spot all add hours. The cheapest quote is not always the lowest total, so compare what each includes. The page on Stockton electrician costs shows how rates and minimums work in general.

How much does an electrical panel inspection cost?

An electrical panel inspection typically costs about $110 to $230 in national price guides. A whole-house wiring inspection costs more, roughly $220 to $490. Prices depend on house size, panel access and how deep the check goes.

a residential electrical service panel with a closed gray door and neatly labeled breakers in a garage wall

A panel inspection is worth getting before you pay for a replacement, because it can show that you need a repair or a subpanel instead. The electrical inspection cost page covers inspection prices in detail, including home inspector checks and permit inspections.

How much does an electrician charge to upgrade an electrical panel?

Upgrading, rather than replacing like-for-like, usually costs $2,500 to $6,000 or more, because it can involve a new meter socket, heavier conductors, a larger main breaker and extra permit steps. Utility work by PG&E is separate, and some of it is paid by PG&E and some by you.

PG&E says that for a panel upgrade it covers items such as the distribution transformer, metering equipment and the underground conductors needed for the new capacity. The customer pays for trenching and permits when trenching is needed. PG&E does not list dollar figures on that page, so ask your electrician what part of the work falls on you.

What else can raise the total:

  • Permit and inspection fees. Fees vary by city and county, so ask what applies.
  • Moving the panel. Relocating from a closet or bathroom adds wire and wall repair.
  • Rewiring or grounding fixes. Bad connections found behind the old panel have to be fixed to pass inspection.
  • AFCI or GFCI breakers. Modern code can call for these on certain circuits, and each one costs more than a plain breaker.
  • Trenching. If the service line is underground and must be replaced, digging adds a lot. See rewiring cost for how bigger wiring jobs are priced.

How much to upgrade an electrical panel from 100 amp to 200 amp?

Going from 100 to 200 amps typically costs about $2,500 to $6,000 in 2026 guides, and the high end covers jobs that need new service wire, a new meter socket or trenching. If the utility has to change equipment, PG&E's process adds time more than cost on your side.

A 200-amp service can help with an EV charger, heat pump or addition. It does not always need a full upgrade. A load calculation shows whether you do. You can read the process in residential electrical panel upgrade, including the PG&E and city steps.

Can a homeowner replace an electrical panel?

In California, a homeowner may be allowed to do electrical work on their own home with a permit as an owner-builder, but panel work is dangerous and the permit and inspection still apply. The feed to the meter stays live, and only PG&E or its authorized contractors may disconnect or reconnect PG&E facilities.

For work done for someone else, California law requires a contractor with a C-10 electrical license from the Contractors State License Board, and the $1,000 small-job exemption does not cover jobs that need a permit. A do-it-yourself panel also leaves out the permit risk, tools and the cost of a failed inspection.

Is there a calculator for what an electrical panel upgrade will cost?

You can make a rough estimate with a short list: start with the job type from the table above, add the permit, add any meter or service work, and add a contingency for wiring repairs. Online calculators do the same arithmetic and give a wide range, so treat the result as a starting point.

A quick method: take the main panel range for your amperage, add $500 to $1,000 if a new meter base or utility work is needed, add the local permit fee, and set aside another 10 to 20 percent for surprises behind the old panel. Then compare it with two or three written quotes.

Questions people ask

What is the 80% rule for electrical panels?

The 80% rule says a breaker should not carry more than 80 percent of its rating for a continuous load, one that runs three hours or more. A 20-amp breaker should carry no more than 16 amps continuously. It applies to circuits, and it is why EV charger circuits are sized above the charger's draw. The panel itself is sized by a load calculation.

Can I upgrade my electrical panel without rewiring my house?

Often yes. A new panel can take the existing circuits if the wiring is in good condition and the connections meet code. If the wires are damaged, overloaded or very old, an electrician may require repairs. See knob and tube wiring for the type of wiring that usually needs more than a panel swap.

Should a 50 year old electrical panel be replaced?

Not automatically, but it should be inspected. A panel that old may have worn parts, a design with a known safety history, or no room for modern loads. If an inspection finds heat damage, corrosion or breakers that will not reset, replacement is the safer choice. If it passes, you may be able to wait.

How long does it take an electrician to replace an electrical panel?

The work on site often takes most of a day for a like-for-like swap, and longer for a service upgrade. The calendar time is longer because of the permit, the PG&E request and the inspection. PG&E says to expect about 30 business days to schedule a disconnect and reconnect, so ask for a timeline in writing.

How often should an electrical panel be replaced in a house?

There is no set interval. Many panels serve for decades. Replace when inspection shows damage or wear, when the panel is full, or when you add big loads. Planning a heat pump, EV charger or addition is a good time to have the panel checked. Ask for quotes from local electricians through the quote form, or visit an electrician in Stockton to see how it works.

Sources used

Last changed