Jump to content

Guide ยท Stockton

Flickering lights at home

Flickering lights can be a worn-out bulb or a wiring fault that needs fixing. This page helps you sort the harmless causes from the risky ones and decide whether to call PG&E or a local electrician.

  1. Fill in the form. It takes about two minutes.
  2. A local specialist gets in touch. They ask a few questions and quote.
  3. You choose. Go ahead only if the price suits you.
a ceiling light fixture with a lit bulb in a dim room

Flickering lights have three common causes: a bulb or dimmer that does not suit each other, a loose connection somewhere in your wiring, or a voltage problem on the utility side. Bulbs and dimmers are harmless and cheap to fix. A loose connection can overheat and needs a local electrician. If the whole neighborhood flickers, PG&E handles it. This page helps you work out which one you have, and what to do next. It is part of our guide to lighting, fans and fixtures.

Why do my lights keep flickering?

Lights flicker because the power reaching the bulb is not steady. The cause might be the bulb itself, a dimmer that is not made for LEDs, a loose wire or switch, an overloaded circuit, or a voltage change from outside your home. Where and when it happens points to the cause: one fixture, one room, one circuit or the whole house.

Notice these clues:

  • One fixture only: usually the bulb, the socket or that switch.
  • One room or one circuit: a loose connection, an overloaded circuit or a failing switch or dimmer.
  • Lights dim when a large appliance starts: a heavy load on the same circuit, or a loose neutral, or a supply that is weak at your home.
  • Every light in the house, and the neighbors too: the utility supply.
  • Lights flicker when turned on, then settle: often a bulb or driver warming up, which is normal for some kinds.

Write down what you see and when. It speeds up any conversation with PG&E or an electrician.

What can I check myself first?

Start with the bulb. Turn the switch off, let it cool, tighten the bulb until snug, or swap in a different one. Then check whether the bulb and dimmer match. An LED on an old dimmer is the most common cause of flicker in a home that has recently changed bulbs. These are safe checks. Do not open walls, panels or fixtures with the power on.

A short list of safe steps:

  1. Replace the bulb with a new one of the same type, or try it in another lamp.
  2. If a dimmer controls the light, set it to full brightness. If the flicker stops, the dimmer is the problem. Look for a dimmer marked for LED loads.
  3. Check whether a plug-in lamp flickers in other outlets.
  4. Notice whether the problem comes with a big appliance, such as the air conditioner starting.
  5. See whether other rooms and the neighbors have the same problem.

Cheap LED bulbs can flicker on their own when the driver is poor, and some flicker is normal in holiday string lights and battery candles. Pot lights and recessed lights that flicker may need a matching LED module or dimmer. The recessed lighting guide has more on that, in how to install recessed lighting.

When do flickering lights point to a wiring problem?

Suspect wiring when the flicker affects several lights on one circuit, comes with buzzing or crackling, makes a switch or cover plate warm, or follows a pattern with the vacuum or a hair dryer. A loose neutral or a loose connection at a switch or fixture can make lights surge brighter and dimmer. This type of fault can overheat, so it is not a wait and see problem.

a ceiling light fixture with a lit bulb in a dim room

Warning signs that belong on the "call now" list:

  • A burning smell or scorched plastic near a switch, outlet or fixture.
  • A warm or discolored cover plate.
  • Crackling, buzzing or sizzling sounds.
  • Some lights getting brighter while others dim.
  • A breaker that trips repeatedly. See why a circuit breaker keeps tripping.

Older homes can add to the risk. Wiring from before the mid-1900s may have worn insulation or loose joints. If your home has old wiring, read what knob and tube wiring is to check for signs.

When should I call PG&E instead of an electrician?

Call PG&E when the flicker affects the whole house and the neighbors see it too, or when it started after a storm or work on the street. PG&E lists flickering lights as a voltage issue you can report to its customer service. It sends a troubleman who checks your service voltage and may leave a recording meter for a few days to collect data.

According to PG&E's voltage page, the troubleman checks whether the service voltage meets the utility's rules. If it does, PG&E tells you the supply is within limits and the issue may be on your side of the meter. That is when you call a local electrician. If you have rooftop solar, tell PG&E when you report it, because the page says to mention it.

If you see downed lines, sparks outside or a burning smell from the meter or panel, stay away and call 911, then PG&E. Do not touch the panel.

When should I call an electrician about flickering lights?

Call a local electrician when only some rooms flicker, when a fix such as a new bulb or dimmer does not stop it, when you notice heat, smell or noise, or when the flicker started after you added new lights or appliances. An electrician can test the circuit under load, tighten connections, check the neutral and find a failing switch or dimmer.

What to expect: California law requires electrical work for others to be done by a contractor holding a C-10 electrical license, so ask for that. Expect a site visit, because a flicker is hard to diagnose from a photo. Ask for a written quote that lists the diagnosis charge and what is included if a repair follows. Tightening a loose connection is often a small job. Replacing a damaged panel part or rewiring a circuit costs more.

To see how to choose, read how to choose an electrician. If the flicker comes with a dead outlet, the outlet and switch electrician page covers that side.

Are flickering lights dangerous?

Sometimes. Most flicker comes from bulbs and dimmers and is only annoying. But a loose connection can arc and heat up, which is a fire risk, and the signs are warmth, smell, buzzing or scorch marks. Treat those as urgent: turn off the circuit if you can do it safely, and call 911 if you see smoke or flames.

A few extra notes:

  • Flicker from LED bulbs on cheap drivers can irritate some people, such as those who get headaches from light. If a particular bulb bothers you, replace it.
  • People who live with photosensitive epilepsy should talk with a doctor about lighting at home. This page is not medical advice.
  • Do not keep a hot fixture on "to see if it settles."

Questions people ask

How long does a flickering lights repair take?

A bulb or dimmer swap takes minutes. An electrician tracing a loose connection often needs one to two hours, depending on how hard the fault is to find. A circuit rewire or a panel repair takes longer. If the cause is a voltage problem, PG&E handles the visit, and a meter may stay for several days.

What should I ask before I hire someone for flickering lights?

Ask whether they hold a C-10 electrical license, whether the visit includes diagnosis, and how they test the circuit. Ask what the charge is if the fix is simple, and whether a repair needs a permit. Get the quote in writing and ask what happens if the flicker returns.

Do I need to be home for flickering lights?

Yes, usually. The electrician needs access to the affected rooms, to the panel and sometimes to the attic. You can also describe exactly when the flicker happens, which speeds up the diagnosis. If you cannot be there, ask a responsible adult who knows where the panel is.

Why do lights flicker when the air conditioner starts?

Starting an air conditioner draws a large surge of current, and that can briefly dim lights on a weak or loose circuit. A brief dip can be normal. A heavy flicker, buzzing or lights that stay dim point to a wiring or supply fault and are worth a call to PG&E or a local electrician.

Can flickering lights mean a bad bulb?

Yes, very often. A bulb that is old, loose or not matched to the dimmer can flicker. Try a new bulb in the same fixture, and try the old bulb in another lamp. If the bulb works elsewhere, the fixture, socket or switch is the cause.

If you want quotes, ask an electrician in Stockton to check the circuit.

Sources used

Last changed